From minor seepage to full basement flooding, JCB Waterproofing and Construction provides engineered solutions that protect your foundation and your investment.
Here is what sets our basement waterproofing team apart from the rest.
Interior perimeter drains installed by our crew are fully sealed, backfilled with clean aggregate, and protected by a lifetime clog-free warranty that transfers to new owners.
Porous concrete block and poured walls let groundwater seep through at the mortar joints -- we seal them from the inside with hydraulic cement and crystalline coatings that bond permanently.
We document every installation with before-and-after photos, moisture readings, and a written record so you have evidence of the work performed and its conditions.
We deliver detailed written quotes that break down every material and labor cost -- no surprise line items appear on your final invoice that were not on the original estimate.
Hydrostatic pressure is the invisible force behind nearly every basement water problem homeowners face in Malvern, OH. When soil around your foundation becomes saturated -- whether from heavy rain, snowmelt, or a high water table -- it exerts outward and downward pressure against concrete walls and floor slabs that can exceed hundreds of pounds per square foot. Over time, this pressure finds the smallest weakness: a tie rod hole, a cold joint between wall and footing, a shrinkage crack in poured concrete, or a deteriorated mortar joint in block construction. Once water finds its path, that path widens with every wet season until a trickle becomes a flood.
Interior drain tile is the most reliable and widely proven basement waterproofing method for existing homes in OH because it manages water that has already entered the wall cavity rather than attempting to stop it at the exterior. The system consists of a perforated pipe, encased in clean washed gravel, installed at or below the footing level in a channel cut along the perimeter of the basement floor. Water that enters the wall-floor joint, seeps through cracks, or migrates through porous concrete flows into this channel and is directed by gravity to a sump basin. A properly sized sump pump then discharges the water away from the foundation. When correctly installed, this system operates indefinitely without clogging because the inlet is protected from sediment by the gravel bed and a filter sock on the pipe.
Wall seepage in block-construction basements is distinct from crack injection because the water is not coming through a single discrete opening -- it is migrating through the porous masonry itself and weeping through the mortar joints. Effective treatment requires sealing the interior face of the block with a hydraulic cement parging coat, followed by a crystalline waterproofing compound that reacts with moisture to form insoluble crystals inside the concrete matrix. This approach stops the migration rather than coating over it, producing a result that actually strengthens with repeated moisture exposure rather than degrading. For severe seepage, core-filling the hollow block cells with grout eliminates the cavity that allows water to travel vertically inside the wall before finding an exit point.
Floor cracks are a separate category of water entry that many homeowners underestimate. A hairline crack in a poured concrete floor can transmit significant water when the slab sits on soil with a high water table. Injection of these cracks follows the same principle as wall cracks: drill ports, install fittings, and pump polyurethane resin that expands to fill the void and bond with the surrounding concrete. In situations where the slab has heaved or settled, crack injection is supplemented with undercutting and re-pouring a portion of the slab to restore a flat, properly sealed floor surface.
A complete basement waterproofing system also requires a reliable, properly maintained sump pump installation. We specify sump pits that are large enough to accommodate both a primary pump and a battery backup pump with sufficient separation that the backup does not interfere with the primary float. Discharge lines are routed to daylight at a point that ensures water flows away from the house and cannot recirculate back to the foundation. Battery backup systems are sized to handle a sustained pumping load during a power outage -- not just a brief test cycle -- because the storm events that knock out power are precisely the events that generate the highest water volume in your basement.
Our full-service waterproofing menu addresses every water entry point from foundation wall to window well.
We size every drain tile system to the specific hydrology of your basement, ensuring the pipe diameter and sump pump capacity match your worst-case water intrusion load.
Poured concrete wall cracks are permanently sealed with low-viscosity polyurethane resin injected under pressure through surface-mounted ports drilled along the crack length.
We test every installation under simulated load conditions before completing the project, verifying pump cycling, float operation, and battery backup activation before we leave.
The finished surface is coated with a heavy-bodied elastomeric masonry waterproofer that bridges hairline cracks and resists surface moisture transmission year-round.
Basement floor cracks that allow water infiltration from below are treated with polyurethane injection resin pumped under pressure to fill the void and bond with surrounding concrete.
We install polycarbonate well covers sized and anchored to each specific well, deflecting direct rainfall while meeting egress requirements and maintaining ventilation.
Our assessment includes a history review of your water intrusion events and a visual inspection of the exterior grading, gutters, and downspouts that affect subsurface drainage.
Our quotes include alternatives at different investment levels so you can choose a phased approach if budget requires it.
Our certified crew completes the installation with minimum disruption to your home, working from a phased sequence designed to protect furnishings and maintain basement access throughout.
We perform a complete post-installation inspection, take final moisture readings, and walk you through the system before issuing your written warranty documentation.
We had serious standing water every spring for eight years. JCB Waterproofing and Construction installed a full perimeter drain and sump system and we have been completely dry through two wet seasons since.
Professional from the initial phone call to the final walkthrough. They explained every step of the process and answered every question without making me feel rushed.
I called three companies before choosing JCB Waterproofing and Construction. They were the only ones who actually measured the moisture levels and explained what was causing our specific problem before quoting a fix.
Get a written quote from certified professionals who have solved every type of basement water problem in OH.
Call +1-866-476-1348 Now